Arduino Development Boards & Accessories

Products

Arduino Uno R3 Starter Kit with RFID

UNO R3 Arduino-compatible starter kit complete with an Uno R3 board and many essential accessories as well as a multitude of parts and modules to start making interesting projects

The Arduino is a great bit of kit for anyone interested in electronics. This kit comes with everything you need to get started with an arduino (apart from a PC to program it). This is the newer RFID version of the kit that contains more usefull sensors and parts to make your introduction to Arduino a better experiance.

Supplied with the kit

Arduino UNO R3

USB A to B 200mm

830 Tie Points Breadboard

10x 200mm Male to Female Jumper Cables

32x Male to Male Jumper Cables

2 x 36 Pin Male Single in Line header

1602 16 character 2 Row backlit LCD Display

I2C SPI Serial Interface Board (LCD Piggyback)

DS1302 Real Time Clock Module

RC522 RFID Kit

7 Segment Single Digit LED Display

7 Segment Four Digit LED Display

8 x 8 LED Dot Matrix

74HC595 8 Bit Shift Register

Water Level Sensor

ULN2003 Four Phase Stepper Motor Driver

28BYJ-48 5V Four Phase Stepper Motor

KY019 5V Relay Module

KY015 Temperature and Humidity Module

KY016 RGB LED Module

KY037 Sound Sensor

KY023 Dual Axis Joystick Module

PP3 Battery Snap with 2.1mm x 5.5mm plug

Infrared Remote Control

Infrared Transmitter/Receiver

4x4 16 Button Matrix

SG90 Servo Motor

2 x SW-520 Tilt Sensor

Active Piezo Buzzer

Passive Piezo Buzzer

10 x Blue LED

10 x Red LED

10 x Yellow LED

3 x Light Dependent Resistor

Flame Sensor/ Infrared Receiver

LM35 Temperature Sensor

10KΩ Linear Potentiometer (Variable Resistor)

10 x 220Ω Resistors

10 x 1KΩ Resistors

10 x 10kΩ Resistors

10 x 330R Resistors

4 x 10mm Tactile Switches

4 x Tactile Switch Caps

Infrared Receiver

Resistor Colour code Chart

CD with projects

Carry Case

Software can be downloaded from the Arduino website here

https://www.arduino.cc/en/Main/Software

Item Number: AUR3K

£37.50 (inc VAT £45.00)

Arduino Uno Revision 3 Development Board

UNO R3 Arduino-compatible board with the ATMega328P, ATMega16U2 and CH340G serial converter

Since Arduino is an "Open Source" hardware as well as software anyone can duplicate the Arduino Uno R3 boards exactly, even using original parts, this means we are able to supply this Arduino compatible board at a fraction of the cost of the original but still working identicaly to the original.

The UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.

Arduino Uno is a microcontroller board based on the ATmega328P (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. The development board has everything needed to support the microcontroler to help you create an endless amount of projects and if you are just starting then the worldwide Arduino community is full of ideas, guides and help to get you started or help you complete your project.

Supplied

1 x Arduino Compatible Uno R3 development board

1 x USB Cable

Software can be downloaded from the Arduino website here

https://www.arduino.cc/en/Main/Software

Item Number: AUR3

£12.00 (inc VAT £14.40)

Resistor Kit Metal Film 1% 600 pieces 10 ohm to 1 Megohm

1% 1/4 Watt Metal Film Resistor Kit in a Handy Carrying Case. Most Popular Values.

This resistor kit comes with 30 different resistor values, suitable for projects, servicing & hobby.

20 pieces per value of the following:

10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 220Ω, 270Ω, 300Ω, 330Ω, 470Ω¸510Ω, 680Ω, 1kΩ, 2kΩ, 2.2kΩ, 3.3kΩ, 4.7kΩ, 5.1kΩ, 6.8kΩ, 10kΩ, 20kΩ, 47kΩ, 51kΩ, 68kΩ, 100kΩ, 220kΩ, 330kΩ, 470kΩ, 680kΩ, 1MΩ.

Item Number: MK600

£8.00 (inc VAT £9.60)

Transparent Case for Arduino Uno R3

Clear Acrylic enclosure for Arduino UNO R3 Board

This custom made box for the Arduino Uno R3 is a simple 2 piece snap together case. It has all the cutouts needed to alow easy connectiion of the power, USB and all the pinheaders. There is also a built in reset button extension to alow easy resetting of the Arduino with a press of the finger (many other cases just have a hole above the reset button). The case will hold the Arduino solidly in place inside without needing you to use any screws. It also has vents on the underside and mounting holes so you can fix the case to a surface.

Dimensions

75mm x 60mm x 17mm

Item Number: ABSR3

£3.00 (inc VAT £3.60)

Arduino Nano Revision 3 Development Board

Arduino compatible board with the ATMEGA328P microcontroller

The Arduino Nano is a small, breadboard-friendly version of the Arduino UNO.

It has the same functionality as the Arduino Duemilanove but at a much smaller size.

The Arduino Nano is well suited for rapid prototyping and as a great general-purpose microcontroller.

Since Arduino is open source hardware & software, anyone can copy the Arduino Nano boards exactly, even using original parts.

We are therefore able to supply this Arduino identical compatible board at a fraction of the cost of the original.

Key Features

Variable Input Voltage (7-12V)

Indicator LEDs for immediate feedback

Compact Form Factor (45mm x 19mm)

14 Digital I/O pins

8 Analog I/O pins

16 MHz clock speed

32kb flash memory (of which 2kb is used by the bootloader)

Software can be downloaded from the Arduino website here

https://www.arduino.cc/en/Main/Software

Item Number: AUN3

£4.75 (inc VAT £5.70)

Data Logger Shield with Real Time Clock for Arduino

Data Logger Shield with Real Time Clock for Arduino Uno

This Arduino compatible shield allows the logging and storage data from an Arduino project to an SD card.

Having a built in Real Time Clock (RTC) insures data accuracyover long time periods and at times where your project may suffer from power loss. Supplied with a CR1220 lithium battery.

Item Number: AUDL

£4.50 (inc VAT £5.40)

LCD screen 16 characters 1 line Arduino compatible

Arduino compatible Backlit LCD screen with 16 Characters on 1 Line

This LCD Screen is a great addition to lots of Arduino projects as well as many other projects.

Specs

Display Format: 16 Characters x 1 Line

Character Size: 3.07mm(W) x 6.56mm(H)

Backlight: Green

Dimensions: 80mm(W) x 36mm(H) x 15mm(T)

Item Number: LCD1601G

£4.00 (inc VAT £4.80)

LCD screen 16 characters 1 line Arduino compatible

Arduino compatible LCD screen with 16 Characters on 1 Line

This LCD Screen is a great addition to lots of Arduino projects as well as many other projects.

Specs

Display Format: 16 Characters x 1 Line

Character Size: 3.07mm(W) x 6.56mm(H)

Backlight: None

Dimensions: 80mm(W) x 36mm(H) x 15mm(T)

Item Number: LCD1610

£3.00 (inc VAT £3.60)

LCD screen 16 characters 2 line Arduino compatible

Arduino compatible Backlit LCD screen with 2 lines of 16 Characters (32 total)

This LCD Screen is a great addition to many Arduino and other projects.

The blue lit screen is blue has white characters and a backlight.

Specification:

Display Format: 16 Characters x 2 Lines (32 total)

Character Size: 3.07mm(W) x 6.56mm(H)

Backlight: Yes

Dimensions: 80mm(W) x 35mm(H) x 11mm(T)

Item Number: LCD1602B

£4.50 (inc VAT £5.40)

Nextion Smart Colour 2.4" LCD Touchscreen with built in Microprocessor

Nextion NX3224T024 2.4" Colour LCD screen with resistive touchscreen

This "Human Machine Interface" (HMI) touchscreen can be used to control your microcontroller as well as display information in real time.

Unlike other similar displays, the Nextion screen incorporates a microprocessor that can be programmed using the Nextion Editor software to display your own custom GUI including programmable buttons, sliders and gauges.

Specification:

Resolution: 320 x 240
Colour: 16-bit 65536 colours
Dimensions: 75mm (L) x 43mm (W) x 6mm (W)

Weight: 26g

Operating voltage: 5VDC

Operating current: 500mA

Item Number: NX3224T024

£29.50 (inc VAT £35.40)

Nextion Smart Colour 3.5" LCD Touchscreen with built in Microprocessor

Nextion NX4832T035 3.5" Colour LCD screen with resistive touchscreen

This "Human Machine Interface" (HMI) touchscreen can be used to control your microcontroller as well as display information in real time.

Specification:

Resolution: 480 x 320
Colour: 16-bit 65536 colours
Dimensions: 100.5mm (L) x 55mm (W) x 5.5mm (W)

Weight: 48.2g

Operating voltage: 5VDC

Operating current: 500mA (typical 145mA)

Item Number: NX4832T035

£45.00 (inc VAT £54.00)

I2C Parallel to Serial Converter for Arduino Type LCD Screens

I2C Paralel to 2 Pin Serial converter for Arduino type LCD screens

This converter can be soldered directly to a standard 1602 LCD screen to convert it to the more convenient 2 pin serial (I2C) used in many Arduino projects.

There is a removable jumper to allow connection with both backlit and non backlit screens.

A potentiometer can adjust the brightness & contrast of the LCD.

Connections

GND = Ground

VCC = 5V

SDA = Serial Data Line

SCL = Serial Clock Line

Item Number: KY1602

£2.50 (inc VAT £3.00)

Prototype Breadboard with 830 points

Solderless Prototype Plug-In Breadboard 0.1 inch - 2.54mm spacing

Ideal for experiments & teaching. 830 Points. 2 x 63 x 5 and 4 x 10 commoned points.

63 rows of 5 points. Self-adhesive backing (or use free-standing).

Can be used over and over again for prototyping circuits.

Useful numbered grid. Accepts IC sockets, ICs and pin strips, transistors, resistors capacitors, LEDs, diodes, wire, etc

Item Number: BB830

£5.25 (inc VAT £6.30)

Prototype Breadboard with 400 points

Solderless Plug-In Breadboard 0.1 inch - 2.54mm spacing. Ideal for experiments & prototyping.

400 Points. 2 x 30 x 5 commoned points. 4 rows of 25 points. Self-adhesive backing (or use free-standing).

Item Number: BB400T

£3.95 (inc VAT £4.74)

65 Breadboard Jumper Leads Solderless

Solderless Jumper Leads for use with Breadboard

This set of coloured jumper leads, invaluable when creating circuits with Breadboard. Seven different colours and Four different lengths will simplify your connections, keeping your work neat and clear to identify.

Colours: Red, Orange, Yellow, Green, Blue, Black and White

Lengths: 120mm, 165mm, 200mm and 240mm

Item Number: JL65

£3.25 (inc VAT £3.90)

40 Female to Female Jumper Cables on rainbow ribbon cable

Solderless Female to Female Jumper Leads in a set of 40

This set of coloured female to female jumper leads can be used togerher or pealed appart into smaller sets or single leads. They are great for prototyping with boards like Arduinos and the Raspbery Pi. With 10 different colours and four of each colour keeping track of what is connected to what nice and easy for quick fault finding.

Colours: Red, Orange, Yellow, Green, Blue, Grey, Purple, Brown, Black and White

Length: 200mm

Item Number: JL40F

£3.00 (inc VAT £3.60)

40 Male to Female Jumper Cables on rainbow ribbon cable

Solderless Male to Female Jumper Leads - set of 40

This set of coloured male to female jumper leads can be used intact, or pealed appart into small sets or single leads. Great for prototyping with Arduino, Raspbery Pi and other projects

It's easy to keep track with 10 different coloursfor easy and quick fault finding.

4 of each: Red, Orange, Yellow, Green, Blue, Grey, Purple, Brown, Black and White

Each length: 200mm

Item Number: JL40

£3.00 (inc VAT £3.60)

Buck Converter DC-DC Step Down 3A Voltage regulator

3A DC-DC Step Down Voltage Regulator (Buck Converter)

This tiny step down voltage regulator uses high frequency switching to make a very efficiant DC-DC converter. It can take 4.5V to 28V and lower it to between 0.8V and 20V at up to 3A(output). The voltage is set with the small in built potentiometer.

Voltage in : 4.5V - 28VDC

Voltage out : 0.8V- 20VDC

Switching Frequency : 1 - 1.5MHz

Maximum Output Current : 3A

Dimensions : 22mm x 17mm

Item Number: BCD3A

£2.50 (inc VAT £3.00)

Buck Converter DC-DC Step Down 9A Voltage regulator

9A DC-DC Step Down Voltage Regulator (Buck Converter)

This step down voltage regulator uses high frequency switching to make a very efficiant DC-DC converter. It can take 5V to 40V and lower it to between 1.2V and 35V at up to 9A(output). The voltage is set with one potentiometer and the constant current can be set with the other from 200mA to 9A.

note: If using this converter at its upper currents then you will need to fan cool the converter.

Voltage in : 5V - 40VDC

Voltage out : 1.2V- 35VDC

Constant Current Range : 200mA - 9A

Maximum Output Current : 9A

Dimensions : 65mm x 48mm

Item Number: BCD9A

£9.00 (inc VAT £10.80)

Buck Converter DC-DC Step Up 10A Voltage regulator

10A DC-DC Step Up Voltage Regulator (Buck Converter)

This step up voltage regulator uses high frequency switching to make a very efficiant DC-DC converter. It can take from 10V to 32VDC in and step it up to a higher voltage from12V to 35VDC at up to 10A(output). The voltage is set with the small multi turn potentiometer.

note: If using this converter at its upper currents then you will need to fan cool the converter.

Voltage in : 10V - 32VDC

Voltage out : 12V- 35VDC

Maximum Output Current : 10A

Dimensions : 65mm x 35mm

Item Number: BCU10A

£8.50 (inc VAT £10.20)

Buck Converter DC-DC Step Up 2A Voltage regulator

2A DC-DC Step Up Voltage Regulator (Buck Converter)

This tiny step up voltage regulator uses high frequency switching to make a very efficiant DC-DC converter. It can take from 2V to 24VDC in and step it up to a higher voltage upto a maximum of 28V at up to 2A(output). The voltage is set with the small multi turn potentiometer.

Voltage in : 2V - 24VDC

Voltage out : 2.5V- 28VDC

Maximum Output Current : 2A

Dimensions : 36mm x 17mm

Item Number: BCU2A

£2.50 (inc VAT £3.00)

EPS8266 WiFi Module 2.4GHz for Arduino with Serial Connection ESP-01

2.4GHz Serial WiFi Module for Arduino and other IOT or Microcontroller projects

The popular ESP8266 microchip with full function WiFi plus it's own microcontroler.

Can be used to add WiFi to your microcontroller project or programmed directly from the Arduino IDE to work independently.

It should NOT be powered from 5V or be directly connected to the digital connections on an Arduino, as this can damage the module. Supplied with a pre-soldered 8 way header.

Voltage : 1.7-3.5VDC

Frequency : 2.4GHz

Wireless Standard : 802.11 b/g/n

Dimensions : 14mm x 25mm

Item Number: ESP01

£4.50 (inc VAT £5.40)

EPS8266 WiFi Module 2.4GHz for Arduino with Serial Connection ESP-12F

2.4GHz Serial WiFi module for Arduino and other IOT or microcontroller projects

This module uses the popular ESP8266 microchip with full function WiFi as well as its own microcontroller. This module can be used to add WiFi to your microntroler project or can be programed directly from the arduino IDE to work independently. This module also has a built in regulator so it can be powered directly from 5VDC. Supplied with 8 way header.

Voltage : 5VDC

Frequency : 2.4GHz

Wireless Standard : 802.11 b/g/n

Dmensions : 24mm x 46mm

Item Number: ESP12F

£6.50 (inc VAT £7.80)

Geared Motor with Wheel

Geared Motor with Wheel and Tyre

This is a 3-9 VDC Motor with a buiIt in gearbox to give speeds of 90-300 RPM (under no load conditions). It is supplied with a 65mm wheel and tyre making it ideal for robot type car projects and more.

Voltage : 3-9VDC

RPM : 90 - 300 no load

Max Current : 200mA

Wheel Diameter : 65mm

Shaft Length : 3.6mm

Item Number: GM65

£3.50 (inc VAT £4.20)

HC-05 Bluetooth Transmitter/Receiver for Serial Communications

Bluetooth transmitter/receier module for serial communication with Arduinos and other microcontrolers

This module is bassed on the CSR standard bluetooth chip. It is a bluetooth transmitter and receiver that can connect to an arduino and allow serial communications to be sent to the arduino wirelesly from another bluetooth device such as a smartphone, a PC or another one of these modules.

Voltage : 3.3-5VDC

Max Current : 30mA

Frequency : 2.4GHz

Baud Rate : 9600 as defult

Dmensions : 15.5mm x 40mm

Item Number: HC05

£6.50 (inc VAT £7.80)

High Speed Micro Motor

N50 High Speed Micro Motor

This micro motor works between 3.7 - 5V DC and spinning at between 27500 RPM @3.7V and 40000 RPM @5V under no load. It is very lightweight at only 10g making it very usefull for small projects, drones or other models.

Voltage : 3.7 - 5VDC

Speed : 27500 - 40000 RPM (no load)

Current : 280mA

Length : 25.5mm Body + 9.5mm Shaft

Width : 10mm x 12mm

Shaft Diameter : 1.0mm

Weight : 10g

Item Number: N50

£2.50 (inc VAT £3.00)

NEO6M GPS Receiver Module with Antenna for Arduino

NEO6M GPS Receiver Module for Arduino or Other Microcontrollers

The NEO6M GPS module is a powerful GPS receiver in a compact package.
It requires very little power to operate and can therefore be powered by battery or it can be powered straight from an Arduino

Voltage : 2.7-3.6VDC

Max supply current: 67mA

Accuracy: 2.5m

Dimensions : 35mm x 25mm

Item Number: NEO6M

£7.50 (inc VAT £9.00)

NodeMcu v3 WiFi Module 2.4GHz with ESP8266, CH340 and USB port

2.4GHz WiFi NodeMcu IoT Development board for Arduino and other IOT projects

This module uses the popular ESP8266 microchip with full function WiFi as well as its own microcontroler, it also has the CH340 USB to Serial converter. This module can be used to add WiFi to your microntroler project or can be programed directly from the arduino IDE to work independently.

Voltage : 5VDC

Frequency : 2.4GHz

Wireless Standard : 802.11 b/g/n

Dmensions : 57mm x 30mm

Item Number: NODEMCU

£6.50 (inc VAT £7.80)

RFID Module Kit with Card and Tag 13.56Mhz

13.56 Mhz RFID Reader and Writer with Tag and Card for use with Arduino or other microcontrollers

A popular and easy to use RC522 RFID module, complete with an RFID card and RFID tag.

Designed to work with Arduino and other microcontrolers.

Can be used to read or write to many different RFID cards, fobs, stickers etc.

Voltage : 3.3VDC

Operating Frequency : 13.56Mhz

Dimensions : 60mm x 40mm

Item Number: RC522

£3.50 (inc VAT £4.20)

SG90 Micro Servo 9g

SG90 Micro Servo for Arduino and other microcontroller projects

This micro servo is the most popular 9g servo in the world, it is used for RC models, robotics and has many other uses. It is compatible with Arduino and other microcontroler projects. Supplied with 3 different servo horns and fixing screws.

Voltage : 5VDC

Speed : 60 Degrees in 0.12 second

Torque : 1.8kg/cm

Wire Length : 150mm

Size : 23x12.2x29mm

Weight : 9g

Item Number: SG90

£2.75 (inc VAT £3.30)

Bestsellers

Arduino Nano Revision 3 Development Board

£4.75 (inc VAT £5.70)

Line tracking sensor module for Arduino KY-033

£2.50 (inc VAT £3.00)

SG90 Micro Servo 9g

£2.75 (inc VAT £3.30)

Breadboard Power Supply 5V / 3.3V

£2.50 (inc VAT £3.00)

Capacitive Touch Sensor Module for Arduino

£1.00 (inc VAT £1.20)

Arduino Development Boards & Accessories

Products

Arduino Uno R3 Starter Kit with RFID

UNO R3 Arduino-compatible starter kit complete with an Uno R3 board and many essential accessories as well as a multitude of parts and modules to start making interesting projects

Arduino Uno Revision 3 Development Board

UNO R3 Arduino-compatible board with the ATMega328P, ATMega16U2 and CH340G serial converter

Resistor Kit Metal Film 1% 600 pieces 10 ohm to 1 Megohm

1% 1/4 Watt Metal Film Resistor Kit in a Handy Carrying Case. Most Popular Values.

Transparent Case for Arduino Uno R3

Clear Acrylic enclosure for Arduino UNO R3 Board

Arduino Nano Revision 3 Development Board

Arduino compatible board with the ATMEGA328P microcontroller

Data Logger Shield with Real Time Clock for Arduino

Data Logger Shield with Real Time Clock for Arduino Uno

LCD screen 16 characters 1 line Arduino compatible

Arduino compatible Backlit LCD screen with 16 Characters on 1 Line

LCD screen 16 characters 1 line Arduino compatible

Arduino compatible LCD screen with 16 Characters on 1 Line

LCD screen 16 characters 2 line Arduino compatible

Arduino compatible Backlit LCD screen with 2 lines of 16 Characters (32 total)

Nextion Smart Colour 2.4" LCD Touchscreen with built in Microprocessor

Nextion NX3224T024 2.4" Colour LCD screen with resistive touchscreen

Nextion Smart Colour 3.5" LCD Touchscreen with built in Microprocessor

Nextion NX4832T035 3.5" Colour LCD screen with resistive touchscreen

I2C Parallel to Serial Converter for Arduino Type LCD Screens

I2C Paralel to 2 Pin Serial converter for Arduino type LCD screens

Prototype Breadboard with 830 points

Solderless Prototype Plug-In Breadboard 0.1 inch - 2.54mm spacing

Prototype Breadboard with 400 points

Solderless Plug-In Breadboard 0.1 inch - 2.54mm spacing. Ideal for experiments & prototyping.

65 Breadboard Jumper Leads Solderless

40 Female to Female Jumper Cables on rainbow ribbon cable

Solderless Female to Female Jumper Leads in a set of 40

40 Male to Female Jumper Cables on rainbow ribbon cable

Solderless Male to Female Jumper Leads - set of 40

Buck Converter DC-DC Step Down 3A Voltage regulator

3A DC-DC Step Down Voltage Regulator (Buck Converter)

Buck Converter DC-DC Step Down 9A Voltage regulator

9A DC-DC Step Down Voltage Regulator (Buck Converter)

Buck Converter DC-DC Step Up 10A Voltage regulator

10A DC-DC Step Up Voltage Regulator (Buck Converter)

Buck Converter DC-DC Step Up 2A Voltage regulator

2A DC-DC Step Up Voltage Regulator (Buck Converter)

EPS8266 WiFi Module 2.4GHz for Arduino with Serial Connection ESP-01

2.4GHz Serial WiFi Module for Arduino and other IOT or Microcontroller projects

EPS8266 WiFi Module 2.4GHz for Arduino with Serial Connection ESP-12F

2.4GHz Serial WiFi module for Arduino and other IOT or microcontroller projects

Geared Motor with Wheel

Geared Motor with Wheel and Tyre

HC-05 Bluetooth Transmitter/Receiver for Serial Communications

Bluetooth transmitter/receier module for serial communication with Arduinos and other microcontrolers

High Speed Micro Motor

N50 High Speed Micro Motor

NEO6M GPS Receiver Module with Antenna for Arduino

NEO6M GPS Receiver Module for Arduino or Other Microcontrollers

NodeMcu v3 WiFi Module 2.4GHz with ESP8266, CH340 and USB port

2.4GHz WiFi NodeMcu IoT Development board for Arduino and other IOT projects

RFID Module Kit with Card and Tag 13.56Mhz

13.56 Mhz RFID Reader and Writer with Tag and Card for use with Arduino or other microcontrollers

A popular and easy to use RC522 RFID module, complete with an RFID card and RFID tag.

Designed to work with Arduino and other microcontrolers.

Can be used to read or write to many different RFID cards, fobs, stickers etc.

SG90 Micro Servo 9g

SG90 Micro Servo for Arduino and other microcontroller projects

Categories

Bestsellers

Account

Links

Help

Contact Us