100 Watt Comprossion Horn Driver - 200W max 100W rms

Reflector horn with 1inch throat, and1¾ inch thread.

Should be connected through a cross-over or capacitor approx 3.3uF bipolar

*  Titanium diaphragm
*  Kapton bobbin
*  Copper clad aluminium voice coil
*  Gold plated spring terminals

Impedance: 8 ohms
Frequency Response: 1500Hz-20000Hz
Diameter: 90mm
Length: 63mm

15 oz Magnet
Power: 100 WattsRMS, 200W Max
SPL @ 1W/1m : 95dB

High quality screw on compression driver. Ideal for use both as a replacement driver or for OEM projects.

High frequency driver for reflector horns fitted with 1inch throat This driver should be connected via a cross-over or Capacitor.
 

Dimensions         98x 51x98mm

Net weight            0.95Kg

Coil Size               25mm   

Freq Response 800-20000

Impedance           8

Magnet Weight      17oz (0.47 kg)

Peak Power          80W

Power RMS           40W

Sensitivity            94dB

High quality screw on compression driver. Ideal for use both as a replacement driver or for new projects.

High frequency driver for reflector horns fitted with 1 3/8inch throat This driver should be connected via a cross-over or Bipolar Capacitor in the range of 2.2uF to 10uF depending on frequency range required. (see our Alcap Range)
 

Dimensions         81x 126x120mm

Net weight            1.6Kg

Coil Size              50mm   

Freq Response  500-20000Hz

Impedance           8 ohms

Magnet Weight     30oz (0.85 kg)

Peak Power          140W

Power RMS           70W

Sensitivity            94dB

Flared 60 Watt Dynamic 8 ohm Horn

A High Quality High Frequency Plastic Horn

Specifications:

• Depth 157mm
• Height  110mm
• Width    290mm
• Colour: Black
• Freq Response 1000 to 18000Hz
• Impedance 8 ohms
• Magnet Weight 280gm
• Music Power 60W (30W RMS)
• Sensitivity 93dBV/Pa

Flared 60 Watt Dynamic 8 ohm Horn

A High Quality High Frequency Plastic Horn

Specifications:

• Depth 145mm
• Height  152mm
• Width    192mm
• Colour: Black
• Freq Response 1000 to 18000Hz
• Impedance 8 ohms
• Magnet Weight 280gm
• Music Power 60W (30W RMS)
• Sensitivity 93dBV/Pa

Piezo Horn Tweeter

Special piezo high impedance tweeter featuring high efficiency without overloading the amplifier.

Connect easily via a series resistor of around 33 ohms 10 Watts. No need for a capacitor.

Crisp, clean reproduction of the high frequencies.

• Power max.150W
• Frequency response4kHz - 30kHz
• Impedance : 1kHz1k ohms
• Impedance : 25kHz
• Dimensions: 145mm x 68mm

Titanium Super Bullet Tweeter 75W RMS

Professional quality tweeter with heavy die-cast aluminium housing fitted with powerful high temperature Titanium voice coil.

Features:
Diecast Aluminium Frame
High Temp Titanium Voice Coil
Max Power: 150W
RMS Power: 75W
Impedance: 8 ohms
Magnet Weight 8 oz
Voice Coil 25mm (1 inch)
Freq Response 1.5KHz - 20KHz
Weight: 726 grams
Dimensions: 80 x 80 x 65mm

SB Acoustics™ SB19ST-C000-4 30W Dome Tweeter 

Professional soft fabric dome tweeter for a smooth frequency response.

 
Features:
 

• Optimized damping in pole cavity to eliminate internal reflection
• Saturation controlled motor system for reduced distortion
• CCAW voice coil for low moving mass
• Long life silver lead wires

Specs:

Nominal Impedance: 4Ω
DC Resistance (Re): 3.4Ω
Voice Coil Inductance (Le): 0.07mH
Effective Piston Area (Sd): 3.8cm²
Voice Coil Diameter: 19.1mm
Voice Coil Height: 1.8mm
Air Gap Height: 3mm
Linear Coil Travel (p-p): 1.2mm
Moving Mass Incl. Air, Mms: 0.22g
Free Air Resonance (Fs): 980Hz
Sensitivity (2.83V/1m): 88.5dB
Mechanical Q-Factor (Qms): 6.45
Electrical Q-Factor (Qes): 1.50
Total Q-Factor (Qts): 1.22
Force Factor (Bl): 1.75Tm
Rated Power Handling: 30W
Magnetic Flux Density: 1.24T
Magnet Weight: 0.13kg
Net Weight: 0.32kg