|Now FREE Delivery on UK mainland orders over £30+VAT|
Strengthened Flexible Crocodile Test leads - Set of 10
A High Quality set of 10 x 500mm test leads in 5 colours, red, black, green, yellow and white. That's 20 soft plastic insulated 25mm crocodile clips.
Essential for engineers, experimenters & hobbyists. Current Rating 2.5A each lead (more if you dare!)
Lead Length: 500mm
Set of 4 Ceramic Coated Tips for many Soldering Irons
Including our AP2 Soldering Station
These bits fit many soldering irons that have a hollow shaft and require a solid tip.
4.75mm diameter. Shaft length 43mm after lip
Coated for long life
1 Pointed bit 0.5mm diameter
1 Pointed bit 0.8mm diameter
1 Chisel shaped bit 45° diameter 3mm
1 Chisel shaped bit 2.7mm
Solderless Jumper Leads for use with Breadboard
This set of coloured jumper leads, invaluable when creating circuits with Breadboard. Seven different colours and Four different lengths will simplify your connections, keeping your work neat and clear to identify.
Colours: Red, Orange, Yellow, Green, Blue, Black and White
Lengths: 120mm, 165mm, 200mm and 240mm
UNO R3 Arduino-compatible board with the ATMega328P, ATMega16U2 and CH340G serial converter
Since Arduino is an "Open Source" hardware as well as software anyone can duplicate the Arduino Uno R3 boards exactly, even using original parts, this means we are able to supply this Arduino compatible board at a fraction of the cost of the original but still working identicaly to the original.
The UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
Arduino Uno is a microcontroller board based on the ATmega328P (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. The development board has everything needed to support the microcontroler to help you create an endless amount of projects and if you are just starting then the worldwide Arduino community is full of ideas, guides and help to get you started or help you complete your project.
1 x Arduino Compatible Uno R3 development board
1 x USB Cable
Software can be downloaded from the Arduino website here
5V relay module for Arduino and other microcontroller projects
This module has a 5V changover relay, protection diode, resistor and LED.
The relay allows the low current microprocessor outputs to switch higher currents and voltages.
Trigger voltage : 5VDC
AC Switch ratings : 250V 10A
DC Switch ratings : 30V 10A
Line tracking sensor module for Arduino and other microcontroler projects
This module uses an IR transmitter and receiver that will detect how reflective the surface is in front of the module. It has a potentiometer to adjust the sensitivity of the module so it can detect if the surface is black or white.
Voltage : 5VDC
Size : 40x12mm
Barometric pressure sensor module for Arduino and other microcontroller projects
This tiny module has a BMP180 precision pressure sensor soldered on to a GY-68 breakout board to make it easy to use this amazing sensor. The BMP180 will give you accurate pressure data via the standard I2C protocol making it simple to add to your project.
Voltage : 1.8 - 3.6VDC
Preasure Range 300hPa to 1100hPa (-500m to 9000m)
Current consumption 0.5µA
Clear Acrylic enclosure for Arduino UNO R3 Board
This custom made box for the Arduino Uno R3 is a simple 2 piece snap together case. It has all the cutouts needed to alow easy connectiion of the power, USB and all the pinheaders. There is also a built in reset button extension to alow easy resetting of the Arduino with a press of the finger (many other cases just have a hole above the reset button). The case will hold the Arduino solidly in place inside without needing you to use any screws. It also has vents on the underside and mounting holes so you can fix the case to a surface.
75mm x 60mm x 17mm
Capacitive touch sensor module for Arduino and other microcontroller projects
One side has a 9mm x 9mm capacitive touch area, and a TTP223 touch sensor IC on the reverse.
An LED indicates when the switch is touched, giving a digital. It can be set either a high or low output, and momentary or latching output by joining or not joining the A and B connections:
A open = High output when touched
A Closed = Low output when touched
B open = Momentary switch action
B Closed = Latching switch action
Voltage : 3 to 5VDC
PCB Size 14x10mm
Login to post a review