|Now FREE Delivery on UK mainland orders over £30+VAT|
Solderless Jumper Leads for use with Breadboard
This set of coloured jumper leads, invaluable when creating circuits with Breadboard. Seven different colours and Four different lengths will simplify your connections, keeping your work neat and clear to identify.
Colours: Red, Orange, Yellow, Green, Blue, Black and White
Lengths: 120mm, 165mm, 200mm and 240mm
UNO R3 Arduino-compatible board with the ATMega328P, ATMega16U2 and CH340G serial converter
Since Arduino is an "Open Source" hardware as well as software anyone can duplicate the Arduino Uno R3 boards exactly, even using original parts, this means we are able to supply this Arduino compatible board at a fraction of the cost of the original but still working identicaly to the original.
The UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
Arduino Uno is a microcontroller board based on the ATmega328P (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. The development board has everything needed to support the microcontroler to help you create an endless amount of projects and if you are just starting then the worldwide Arduino community is full of ideas, guides and help to get you started or help you complete your project.
1 x Arduino Compatible Uno R3 development board
1 x USB Cable
Software can be downloaded from the Arduino website here
5V relay module for Arduino and other microcontroller projects
This module has a 5V changover relay, protection diode, resistor and LED.
The relay allows the low current microprocessor outputs to switch higher currents and voltages.
Trigger voltage : 5VDC
AC Switch ratings : 250V 10A
DC Switch ratings : 30V 10A
Microphone sound sensor module for Arduino and other microcontroler projects
This module uses a minature microphone to detect sound levels. It also has a comparator to give a digital output as well as an analogue output and potentiometer to adjust the level for the digital output.
Voltage : 5VDC
Line tracking sensor module for Arduino and other microcontroler projects
This module uses an IR transmitter and receiver that will detect how reflective the surface is in front of the module. It has a potentiometer to adjust the sensitivity of the module so it can detect if the surface is black or white.
Voltage : 5VDC
Size : 40x12mm
Finger heartbeat measuring sensor module for Arduino and other microcontroller projects
This module uses abright IR LED and a phototransistor. When a finger is placed between the LED and transistor you will get an analogue output of light intensity that passes through the finger, this will vary every time the heart beats and indicate heart rate.
Voltage : 5VDC
Ultrasonic ranging module for Arduino and other microcontroller projects
This module has a 40kHz ultrasonic transmitter and receiver pair mounted on the front of a small PCB along with the required control circuitry on the back. The module works by sending a short 40kHz square wave out and timing how long it takes to return to the module, you can then work out the distance it has traveled by knowing the speed of sound.
Voltage : 5VDC
Working Range : 20mm to 4500mm
Accuracy : 2mm
Soil hygrometer module with digital and analogue outputs for Arduino and other microcontroler projects
This module has a seperate 2 pronged moisture detector that is inserted into the soil and then connected to the comparitor board using the supplied link wires. It can give out a digital (High/Low) signal at a certain moisture level that can be set by adjusting the potentiometer on the board. There is also an analogue output to give you a more precise reading of the moisture level in the soil.
Voltage : 3.3 to 5VDC
Comparitor PCB Size 30x16mm
Barometric pressure sensor module for Arduino and other microcontroller projects
This tiny module has a BMP180 precision pressure sensor soldered on to a GY-68 breakout board to make it easy to use this amazing sensor. The BMP180 will give you accurate pressure data via the standard I2C protocol making it simple to add to your project.
Voltage : 1.8 - 3.6VDC
Preasure Range 300hPa to 1100hPa (-500m to 9000m)
Current consumption 0.5µA
Login to post a review