Stripboard 2.54mm - 0.1 inch Copper Strips perforated at 0.1 inch (2.54mm) sacing 95 X 127mm
Solderless Plug-In Breadboard 0.1 inch - 2.54mm spacing. Ideal for experiments & prototyping.
400 Points. 2 x 30 x 5 commoned points. 4 rows of 25 points. Self-adhesive backing (or can be used free-standing).
Solderless Plug-In Breadboard 0.1 inch - 2.54mm spacing
Ideal for experiments or teaching. 830 Points. 2 x 63 x 5 and 4 x 10 commoned points. 63 rows of 5 points. Self-adhesive backing (or can be used free-standing).
Can be used over and over again for prototyping circuits. Useful numbered grid. Accepts IC sockets, ICs and pin strips as well as discrete devices such as transistors, resistors capacitors, LEDs, diodes and many more.
Solderless Jumper Leads for use with Breadboard
This set of coloured jumper leads, invaluable when creating circuits with Breadboard. Seven different colours and Four different lengths will simplify your connections, keeping your work neat and clear to identify.
Colours: Red, Orange, Yellow, Green, Blue, Black and White
Lengths: 120mm, 165mm, 200mm and 240mm
UNO R3 Arduino-compatible board with the ATMega328P, ATMega16U2 and CH340G serial converter
Since Arduino is an "Open Source" hardware as well as software anyone can duplicate the Arduino Uno R3 boards exactly, even using original parts, this means we are able to supply this Arduino compatible board at a fraction of the cost of the original but still working identicaly to the original.
The UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
Arduino Uno is a microcontroller board based on the ATmega328P (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. The development board has everything needed to support the microcontroler to help you create an endless amount of projects and if you are just starting then the worldwide Arduino community is full of ideas, guides and help to get you started or help you complete your project.
1 x Arduino Compatible Uno R3 development board
1 x USB Cable
Software can be downloaded from the Arduino website here
Bi-colour Red/Green 5mm LED module for Arduino and other microcontroler projects
This module is a 2 coloured 5mm LED with a common cathode that will iluminate either Red, Green or Orange (Red and Green together). You will need to use a resistor when connecting to an Arduino.
Voltage : 2.0 to 2.5VDC
Current : 10mA
Key switch module for Arduino and other microcontroler projects
This module has a smalltactile switch that is normaly open and will close when pressed, it has a resistor connected in series with the switch so it can be used directly with a digital input on an Arduino when powered by 5VDC.
Voltage : upto 12VDC
RGB full colour 5MM LED module for Arduino and other microcontroler projects
This module has a 5MM RGB LED that can be used to create virtually any colour by varying the intensity of the 3 colours by using the PWM output to each pin. Resistors will be needed to connect to an Arduino.
Voltage : Red 1.8 to 2.4VDC
Green 2.8 to 3.6VDC
Blue 2.8 to 3.6VDC
5V relay module for Arduino and other microcontroler projects
This module has a 5V changover relay, protection diode, resistor and LED. This relay will allow the low current outputs from your microprocessor to switch much higher currents and voltage so you can control larger things from a digital output pin.
Triger voltage : 5VDC
AC Switch ratings : 250V 10A
DC Switch ratings : 30V 10A
Login to post a review