|Now FREE Delivery on UK mainland orders over £30+VAT|
NPN TO92 CBE 45V 100mA
IC Voltage Regulator Adjustable +1.2-37V 1.5A TO220
Black Cable Ties 200mm Long x 3.5mm thick. 100 pack
Self Adhesive Cable Ties Bases 100 pieces. Strong Nylon
19 x 19mm with 4 slots to fit cable ties up to 3.6mm. Natural Colour 100 pack
Nylon 66 Temp range: -40 to 81C
Lithium Thionyl Chloride Battery 3.6V 2400mAH AA Size 15 x 50mm
Also known as ER14500, ER14505
Non rechargeable. Recommended for reliable and heavy duty use.
High Reliability. 1% per annum discharge rate - 10 year shelf life
Product Picture is representative and may vary.
Arduino compatible board with the ATMEGA328P microcontroller
The Arduino Nano is a small, breadboard-friendly version of the Arduino UNO.
It has the same functionality as the Arduino Duemilanove but at a much smaller size.
The Arduino Nano is well suited for rapid prototyping and as a great general-purpose microcontroller.
Since Arduino is open source hardware & software, anyone can copy the Arduino Nano boards exactly, even using original parts.
We are therefore able to supply this Arduino identical compatible board at a fraction of the cost of the original.
Variable Input Voltage (7-12V)
Indicator LEDs for immediate feedback
Compact Form Factor (45mm x 19mm)
14 Digital I/O pins
8 Analog I/O pins
16 MHz clock speed
32kb flash memory (of which 2kb is used by the bootloader)
Software can be downloaded from the Arduino website here
Slide-fit over many solid soldering iron shafts
Coated tips for long life.
Shaft: length 65mm, diameter 7.1mm
71mm shaft length
1 of each tip:
2.7mm chisel face
UNO R3 Arduino-compatible starter kit complete with an Uno R3 board with essential accessories plus a multitude of parts and modules to start building interesting projects
The Arduino is a great bit of kit for anyone interested in electronics.
This kit comes with everything you need to get started with an Arduino (apart from a PC to program it).
This is the newer RFID version of the kit containing more usefull sensors and parts to make your introduction to Arduino a better experiance.
Supplied with the kit:
Arduino UNO R3
USB A to B 200mm
830 Tie Points Breadboard
10x 200mm Male to Female Jumper Cables
32x Male to Male Jumper Cables
2 x 36 Pin Male Single in Line header
1602 16 character 2 Row backlit LCD Display
I2C SPI Serial Interface Board (LCD Piggyback)
DS1302 Real Time Clock Module
RC522 RFID Kit
7 Segment Single Digit LED Display
7 Segment Four Digit LED Display
8 x 8 LED Dot Matrix
74HC595 8 Bit Shift Register
Water Level Sensor
ULN2003 Four Phase Stepper Motor Driver
28BYJ-48 5V Four Phase Stepper Motor
KY019 5V Relay Module
KY015 Temperature and Humidity Module
KY016 RGB LED Module
KY037 Sound Sensor
KY023 Dual Axis Joystick Module
PP3 Battery Snap with 2.1mm x 5.5mm plug
Infrared Remote Control
4x4 16 Button Matrix
SG90 Servo Motor
2 x SW-520 Tilt Sensor
Active Piezo Buzzer
Passive Piezo Buzzer
10 x Blue LED
10 x Red LED
10 x Yellow LED
3 x Light Dependent Resistor
Flame Sensor/ Infrared Receiver
LM35 Temperature Sensor
10KΩ Linear Potentiometer (Variable Resistor)
10 x 220Ω Resistors
10 x 1KΩ Resistors
10 x 10kΩ Resistors
10 x 330R Resistors
4 x 10mm Tactile Switches
4 x Tactile Switch Caps
Resistor Colour code Chart
CD with projects
The Arduino IDE Software can be downloaded from the Arduino website here
You can download a copy of the included CD here
64GB USB 3 Flash drive features USB 3.0 for ultra fast and easy transfers. It's backwards compatible with existing USB 2.0 ports.